Master Bath Project--Framing

This was a very intricate framing job.  The tub height had to match the windowsill, the shower seat had to be the right height for the glass doors, and the tub steps had to look natural which was pretty tough considering all the angles we were dealing with.  We started with a plan, and it changed more times that I can count.  I am so glad that Randy and Tim took over when they did cause I turned out great.  

Tub on platform, checking to make sure that the height of the tub is correct. 




My plumbing job for the secondary shower head on the left, and primary on the right.  The bucket is there because I was pressure testing the plumbing. 


Here's the tub enclosure ready for backer board.


And now with Backer Board




Randy Setting the Curb and getting ready to pour the concrete shower base.



Shower base poured, ready to install the backer board in the shower. 
Backer Board installed.....
Randy Installing the moisture barrier or waterproof membrane. 


And now we are ready for tile......

Master Bathroom Project--Before Pictures

With the fireplace complete, it was time to get to work on the Master Bath. We had purchased a Jacuzzi Jetted corner tub for the bathroom and now needed to build the tub platform (tub sat too low on the floor to allow us to enjoy the view), the tub enclosure, and the custom shower base & enclosure. This was a fairly intimidating project and lucky for us, our Friend Eric, who helped us with the fireplace, knew someone. Randy Zito is one of Eric's buddies and like Eric, was looking for work after the Yellowstone Club construction shut down. He and his Brother Tim run a Tile business called Pro-Tile. He not only had the time, but he had a bunch of Travertine Tile. For those of you that are not familiar with Travertine, it is not ceramic tile, it is actually a quarried and cut stone. Extremely expensive stuff when you compare it to ceramic tile. Randy and Tim had the experience and needed the work so we got a great deal on the whole thing.

Here are the before Pictures:

Fireplace Mantle

Ohh my god I'm ready to be done with this house......But I digress.  

The rock work looks so good up there but a fireplace just isn't complete without a Mantle.  I made this mantle from one of the leftover logs.  It's Ponderosa pine and it has a bit of rustic detail to it.  

I had to rip the log in half, chisel off the tongue's, draw-knife the imperfections, and then sand forever.  Once I had it sanded down to about where I liked it, I switched to finer and finer grits until it was really nice and smooth.  Then it was time for the poly-acrylic stain/sealer.  It took 4 coats (sanding between coats with 320 grit) to make it look this nice.  

The mantle is held up by two "Corribles" that were just two pieces of firewood I drug off the woodpile and gave the same treatment.   I'd like to think that it turned out pretty good.  

All that is left is trim, hearthstone, and a light fixture.  

Great Room Fireplace Part 3--Finished Product

As the title says, here is how it turned out.  Help from friends and family made this possible.  Thanks to Brandon, Eb, my folks, and Eric.  Without you guys it would not have turned out anywhere near this nice.  Now it's time for some trim.  

Great Room Fireplace Part 2

With the fireplace in and functional, it was time to put up the rock. I was planning on doing it myself until I found out that a buddy of mine from High School was also looking for work. Eric and I used to party together in High School and since we last bumped in to one another, has gone on to become a Master Mason. Having worked steadily in the Yellowstone Club near Big Sky, Montana, his experience in the masonry field and his availability made this an easy decision to make. It did cost me some whiskey.....

Sorting the rock into simmilar shaped pieces.  What a mess. 
Masking the fireplace. 
Emily spraying the backerboard with water to help with adhesion.  
Eric sets the first stone. 

Eric designed an arch to match the front of the fireplace.  Had to cut a stone to make the "Keystone".  The soldiers that stand on either side took very little work.  
Setting up for a cut.  Eric marks the stone, I cut it.  Judging by the saw angle this one that Eric asked me to "Knife edge" to help hide the cut.  
The saw is my 10" dewalt compound miter chop saw.  It has done everything from cutting decking in Absarokee, cutting rafter boards in Nevada, Cutting wall boards in Alaska, rebar on the foundation, and now cutting stone for the fireplace.  

Eric cleaning up and tooling the joints on the low stuff.  Ready to go up. 
Setting up a platform for the work up high.  
Eric laughing at my diamond saw antics, another stone toasted....
It started snowing, so that made cutting the stone's that much more fun.  




Eric is smiling, cause this is the last stone.  
Done!! Now time for cleanup.  
Tooling the joints (scraping away excess mud) and cleaning mud off of other stones.  
Putting away tools and cleaning up the mess we have made.  

Great Room Fireplace Part 1

After basking in the glow of the finish in September, it was time to get back to work. Things were not progressing real fast with hunting season in full swing but things were to change. In early November, all 570 employees of the East Boulder Mine were cut loose. This meant I had lots more time on my hands. During the first week I spent a lot of time hunting but reality soon set in. If I did not receive a call back I would need to have things ready to sell.

While I was in Billings I picked up all of the supplies we needed to install and finish the Great Room Fireplace and set out to get it done. The fireplace is made by Vermont Castings, and it sells new for around $4000 without the fancy Roman Bronze Arch front cover, which is another $1200. This was a floor model and the company had discontinued the model so we got it for about $2900. The venting supplies cost another $400 and I think I spent another $50 or $60 on propane piping. The stone came from a company in town called All Stone. 53 total square feet of multi-colored cobble stone, mason mix, and lath cost us another $370. All together it was a considerable expense for us considering the employment situation but if we needed to sell the house, it had to be done.

Once we got the material home I started by building the platform inside the fireplace enclosure and setting the stove in place. Kevin Eberle came over one day and helped me run the propane piping and then Brandon came over on Thanksgiving and helped me install the chimney venting. Once that was complete the fireplace was functional. Time for the rock!







The stove is actually running in this picture.